iti Fitter Question and Answer Hindi and English 2021

0
16

iti Fitter Question and Answer Hindi and English 2021- For the students who are doing ITI from iti Fitter, today questions and answers have been given in this post, this question was asked in previous years exam so you read these questions carefully and this question Competition exams are asked in exams like DMRC, Railway, if you find this post beneficial, then share it with your friends.

Note: This question is question and answer asked in iti fitter trade from 2014 to 2019 

Question 1. Which gauge is used to check tool made for metric bangle?
Answer . center gauge

Question 2. What are the metal particles stuck in the file called?
Answer . pinning of file

Question 3. What is the distance covered by a drilling machine in 1 minute called?
Answer . cutting speed

Question 4. Which scriber is used with Vernier height gauge?
Answer . off set scriber

Question 5. How many degrees is the chisel cutting angle of the drill?
Answer . 120 to 135 degrees

Question 6. With which part of the combination set does the scriber go?
Answer . square head

Question 7. Where is hatchet steak used?
Answer . to fold

Question 8.Dye is made of which metal material?
Answer . high carbon steel

Question 9.Which rivet is used for riveting aluminum plates?
Answer . aluminum rivet

Q10.Which steak provides double ended shelter?
Answer . horse steak

Question 11. What is the distance from one point of a bangle to the same point of another bangle on a screw thread called?
Answer . pitch

Question 12. What is used to remove a broken tap in a hall?
Answer . stud extractor

Question 13.Which dye is used to cut bangles on a road in the middle of a hole?
Answer . acron dye

Question 14. After washing in slip gauge tetrachloride, which cloth is used to clean it?
Answer . wiped clean with lilan cloth

Question 15. What is used to make a flat surface on the top surface of the hole or the face of the bore after a hole has been made in a molded job?
Answer . spot facing

Question 16. What is a wing nut called ?
Answer . Palai Nut

Question 17.Lock opening is used to open which lock?
Answer . to open the circular lock on the shaft

Question 18. How many degrees is the point angle of a dot punch?
Answer . 60°

Question 19. Which rivet is used in aircraft?
Answer . pope rivet

Question 20. Which metal is the hand vise made of?
Answer . mild steel or cast iron

Question 21.————What is used to put and remove coal in the furnace?
Answer . shovel

Question 22. How many types of angle plates are there?
Answer . 1. Plain solid angle plate 2. Slotted angle plate 3. Swivel angle plate 4. Box angle plate

Question 23. What type of tool is a caliper?
Answer . indirect gauge

Question 24. What is the size of Snap Gauge?
Answer . C shape

Question 25.Which is used to level the surface of the job?
Answer . flutters

Question 26. The front part of the flat file is in taper?
Answer . 1/3 part

Question 27.————Used to draw a parallel line or line on a round job?
Answer . seat rule of

Question 28. Which bearing is suitable to take axial thrust as well as radial load?
Answer . Contact

Question 29. What is the weight of sledge hammer in KG?
Answer . 2kg to 10kg

Question 30. What is the bent lag of a jenny caliper approximately?
Answer . 5 millimeters at 450

Question 31. What is the first cut on the face of the file called?
Answer . overcut

Question 32. Major Diameter ———— What is the largest diameter?
Answer . screw shred

Question 33.Which metal is the vice clamp made of?
Answer . aluminum

Question 34. Which dye is used to clean old bangles?
Answer . die nut

Question 35. The cutting edge of high carbon steel chisel is approximately hard and tamper up to how many mm?
Answer . 25MM to 35MM

Question 36. What is Parallel Block?
Answer . rectangular

Question 37. The stand of the marking table is made of which metal?
Answer . mild steel

Question 38.Soldering is a type of fastener?
Answer . semi permanent

Question 39. Which gauge is used to align the lathe tool?
Answer . center gauge

Question 40. Tool maker clamp is used for—
Answer . For clamping parallel and finish job

Question 41. What is the distance of the edge of the center of riveting from two lines?
Answer . 1.5D

Question 42. What is the thickness of the hexon blade in how many mm?
Answer . 0.63 mm to 0.80 mm

Q43.The accuracy of surface plate is measured in percentage high sport?
Answer . per square centimeter

Question 44. Which rivet is used for light work?
Answer . pallet head rivet

Q45. Job is checked by TrySquare?
Answer . 90 degrees

Question 46. On both the sides of L-Square are the marks marked?
Answer . inches, centimeters

Question 47. The point of the punch is called——
Answer . hard and temper

Question 48. Helix angle is kept in helical gear?
Answer . 25-45

Question 49. To what degree does the disc make up?
Answer . 0 to 180 degree

Question 50. Which bolt is used to lift heavy machines?
Answer . eye bolt

iti Fitter Question and Answer in English 2020

Question 1. Which gauge is used to check the tool made for a metric bangle?
Answer . center gauge

Question 2. Metal particles get trapped in the file. What are they called?
Answer . Pinning off file

Question 3. What is the distance the drilling machine covers in 1 minute?
Answer . Cutting speed

Question 4. Which scriber is used with Vernier height gauge?
Answer . Offset scriber

Question 5. To what degree is the cheese cutting angle of a drill?
Answer . 120 to 135 degrees

Question 6. Which part of the combination set is the scriber?
Answer . squarehead

Q 7. Where is hatchet steak used?
Answer . To fold

Question 8. The dye is made of which metal material?
Answer . high carbon steel

Question 9. Which rivet is used for reviving aluminum plates?
Answer . Aluminum rivet

Q 10. Which steak provides double-ended shelter?
Answer . Horse steak

Question 11. What is the distance from one point of a bangle to the same point of another bangle on the screw shred?
Answer . The pitch

Question 12. Which is used to remove a broken tap in a hall?
Answer . Stud extractor

Question 13. Which dye is used for cutting bangle on a road in the middle of a hole?
Answer . Akron Dye

Question 14. With which cloth is it cleaned after washing in slip gauge tetrachloride?
Answer . Lilian is cleaned with a cloth

Q15. Which is used to make a flat surface on the top surface of a hole or the face of a bore after opening a hole in a cast job?
Answer . Spot facing

Question 16. Wings are called nuts?
Answer . Pulp nut

Question 17. Which locking is used to open the lock?
Answer . Open the circular lock on the shaft

Question 18. How many degrees is the point angle of the dot punch?
Answer . 60 °

Q19.Which rivets are used in aircraft?
Answer . Pope rivet

Question 20. Hand metal is made of which metal?
Answer . Mild steel or cast iron

Question 21. ——– is used to pour and remove coal in the furnace?
Answer . Shoval

Question 22. What type of Angle Plate is there?
Answer . 1. Plane Solid Angle Plate 2. Slotted Angle Plate 3. Swivel Angle Plate 4. Box Angle Plate

Question 23. What type of tool is a caliper?
Answer . Indirect scale

Question 24. What size is the snap gauge?
Answer . C size

Question 25. Which is used to level the surface of the job?
Answer . Flutters

Question 26. The front part of the flat file is in the taper?
Answer . 1/3 part

Question 27 .——- Used to draw a parallel line or line on a round job?
Answer . Seat rule

Question 28. Which bearing is suitable for taking radial load along with axial thrust?
Answer . Contact

Question 29. How much KG does the sleigh hammer weigh?
Answer . 2kg to 10kg

Question 30. What is approximately the folded leg of Jenny caliper?
Answer . 5 millimeters at 450

Question 31. What is the first cut on the face of a file called?
Answer . Overcut

Question 32. Does measure diameter have the largest diameter?
Answer . Screw shred

Question 33. Which clamp is made of which metal?
Answer . Aluminum

Question 34. Which dye is used to clean old bangles?
Answer . Die nut

Question 35. Cutting age of high carbon steel cheese is approximately how many MMs are hard and tamper?
Answer . 25mm to 35mm

Question 36. What is a Parallel Block?
Answer . Rectangular

Question 37. Which metal is made of the marking table stand?
Answer . mild steel

Question 38. Soldering is a type of fastener?
Answer . Semi-permanent

Question 39. Which gauge is used to align the lathe tool?
Answer . center gauge

Question 40. Toolmaker clamp is used for—
Answer . To clamp parallel and finish jobs

Question 41. What is the distance of the edge of the riveting centers from two lines?
Answer . 1.5D

Question 42. How many mm is the thickness of a hexagon blade?
Answer . 0.63 mm to 0.80 mm

Question 43. Accuracy percentage of the surface plate is measured in high sport?
Answer . Per square centimeter

Question 44. Which rivet is used for light works?
Answer . Plate head rivet

Question 45. Does Trai Square check the job?
Answer . 90 degrees

Question 46. What are the marks on both sides of L-Square?
Answer . Inch, centimeter

Question 47. What is the point of five?
Answer . Hard and temper

Question 48. The helix angle is kept in the helical gear?
Answer . 25-45

Question 49. To what degree is the disk made?
Answer . 0 to 180 degrees

Question 50. Which bolt is used to lift heavy machines?
Answer . Eyebolt

Today in this post iti fitter trade objective type question answer pdf download, fitter shop 1000 questions-answers pdf download, iti fitter objective type question answer pdf in Hindi, iti fitter 1st-semester question paper 2017, iti fitter question and answer iti fitter trade If you have any question related to theory pdf free download, iti fitter online test in English, iti fitter practical book pdf Hindi, iti fitter 2nd sem question paper pdf free download, then definitely tell us in the comment box. And if you find this information beneficial, then do share it with your friends.

LEAVE A REPLY

Please enter your comment!
Please enter your name here