iti Machinist Question Paper Hindi and English Pdf 2021

0
16

iti Machinist Question Paper Hindi and English Pdf 2021 – For the students who are doing ITI from iti Machinist, today questions and answers have been given in this post, this question was asked in previous years exam so you read these questions carefully and this question Competition exams are asked in exams like DRDO, NTPC, DMRC, Railway, if you find this post beneficial, then share it with your friends.

 Note: This question is a question and answer asked in Machinist trade from 2012 to 2019 

Question 1. What is the shape of the cheese?
Answer . octagon

Q2.Which scriber’s length can be adjusted according to the function?
Answer . adjustable scriber

Question 3. Are there temporary fastenings?
Answer . Key, Pin Screw, Nut Bolt, Stud

Question 4. Which metal is the square head made of?
Answer . cost steel

Question 5. The body of the file is raised slightly in the middle, what is it called?
Answer . Conversity

Q6.Which side of the blade is placed during the hexon frame cutting action?
Answer . forward

Question 7. Which hammer’s pen is in the cross of the handle?
Answer . cross pen hammer

Question 8. Which edge of the sheet is folded once to make——
Answer . single hem

Question 9. The teeth of which gear are parallel to the axis and are used to transfer motion parallel shafts?
Answer . spur gear

Question 10. What is the part of the shaft in the bearing called?
Answer . Journal

Question 11. What is the process of expanding the head of a cheese called?
Answer . mushroom head

Question 12. Which hammer is used to remove nails from wood?
Answer . claw hammer

Question 13. On the round file—— teeth are thorns?
Answer . single cut

Question 14. Which metal is the scriber made of?
Answer . high carbon steel

Question 15. The metal of the bearing is used for low speed and high load?
Answer . cast iron

Question 16. What is the hardness of slip gauge?
Answer . 63 HRC

Question 17. Which steak is also used for making flange edges of utensils?
Answer . crescent steak

Question 18. Surface gauge is used for———
Answer . To remove the center on a lathe machine

Question 19.Solid punch is used for?
Answer . to poke holes in the sheet

Question 20. What is the angle made by the two sides of the thread when they meet together called?
Answer . thread angle

Q21.How are the legs of the jenny caliper?
Answer . One leg is straight and the other leg is bent inward

Question 22. Which nut is used in hexon frame?
Answer . Wing nut also called fly nut

Q23.What is used to get the desired fit?
Answer . filler gauge

Q 24. In what ways can the filing be done?
Answer . Draw Filing, Straight Filing, Cross Filing, Circular Filing

Question 25. The edges of the sheet are folded in a special way and stuck together, what is it called?
Answer . seam

Question 26. What is the head file called?
Answer . safe as file

Question 27. How is the screw rod cut on the cylindrical surface?
Answer . making helical groove

Question 28. What is the shape of the eye hall of a head hammer?
Answer . elliptical

Question 29. Which drives are prone to slipping?
Answer . belt drive

Question 30.Dift punch is used for what purpose?
Answer . to halve thin sheets together

Question 31. Which metal is the tip of a soldering iron made of?
Answer . of copper

Question 32. What is the distance between one dot punch to another dot punch?
Answer . 3 to 5mm

Question 33. At what temperature is the gauge kept in the workshop?
Answer . 20°C

Question 34. What is the ratio of round taper?
Answer . 1:50

Question 35. Which bolt has 6 sides which are used in simple works?
Answer . hexagonal head volt

Question 36. Helical torsion spring is used for what purpose?
Answer . done in the career of cycling

Question 37. What is the range of bangles in the pitch gauge?
Answer . 0.25mm to 6mm

Question 38. At what degree can the blade of the trip be grinded?
Answer . at 80 degrees

Question 39. Which punch is used to confirm the marking done on the job?
Answer . dot punch

Question 40. For what purpose is leaf spring used?
Answer . It is mostly used in automobile vehicles.

Q41.What is the size of C clamp?
Answer . C shape

Question 42. What type of tool is a steel rule?
Answer . direct gauge

Question 43. What is the apex angle of Iron V block?
Answer . 90 degrees

Question 44. The width of the hexblade can be up to how many mm?
Answer . 13mm to16mm

Q45. According to the Institute of Standards, in which range the radius is found?
Answer . 0.6mm to 25mm

Question 46. How many bangles are there in taper in medium type?
Answer . 3 to 4 bangles

Q47.Bearing loose pulley is the one which moves in the form of?
Answer . free form

Question 48. Which punch is used for soft metal?
Answer . pickup punch

Question 49. The cutting edge of cheese is made of?
Answer . Convex

Question 50. At what length are cheeses found?
Answer . 150 to 200mm

Question 51. What is the setting of the teeth of a blade called?
Answer . setting of teeth

Question 52. Enlarging a small difference is said to be correct?
Answer . dial test indicator

Question 53. The machine tool is used to align the slide vertically and horizontally?
Answer . block level experiment

Question 54. What is the melting point of solder?
Answer . 205 to 450

Question 55. Two shafts have to be set at a 90 degree angle to transmit motion or at a particular angle which gear is used?
Answer . Bevel gear

Question 56. What is used to remove the pieces of burnt coal from near the nozzle?
Answer . rack and poker

Question 57.Think rule is used by——
Answer . pattern maker

iti Machinist Question Paper In English Pdf 2020

Question 1. What is the water size?
Answer . Octagon

Question 2. Which scriber length can be adjusted according to function?
Answer . Adjustable scriber

Question 3. Does temporary fastening occur?
Answer . Key, pin skew, nut bolt, stud

Question 4. What is a square head made of metal?
Answer . cost steel

Question 5. The body of the file rises in the middle, what is it called?
Answer . Convaqisti

Question 6. Which side is held to be the teeth of the blade during the hacksaw frame cutting action?
Answer . Forward

Question 7. Which hammer pen is in the cross of the handle?
Answer . Cross pen hammer

Question 8. Which side of the chadar is once folded and made?
Answer . Single hem

Question 9. Which gears have their teeth parallel to the axis and are used to transfer the speed parallel to the shaft?
Answer . Spur gear

Question 10. What part of the shaft is in the bearing is called?
Answer . The journal

Question 11. What is the action of spreading the head of a chisel?
Answer . Mushroom Head

Question 12. Which hammer is used to remove the nail from wood?
Answer . Claw hammer

Question 13. On the round file – are the teeth Dante?
Answer . Single cut

Question 14. Which metal is a scriber made of?
Answer . high carbon steel

Question 15. Bearing metal is used for low speed and high load?
Answer . cast iron

Question 16. What is the hardness of a slip gauge?
Answer . 63 HRC

Question 17. Which steak is also used to make flange edges of utensils?
Answer . Crescent steak

Question 18. Surface Gauge is used?
Answer . To remove the center on the lathe machine

Question 19. Solid punch is used for this work?
Answer . To prick the sheet

Question 20. What angle would you call the two sides of the thread after meeting each other?
Answer . thread angle

Question 21. How does Jenny Caliper have legs?
Answer . One leg is straight and the other leg is turned inwards.

Question 22. Which nut is used in a hacksaw frame?
Answer . Wingnuts are also called fly nuts.

Question 23. What is used to achieve the desired fit?
Answer . Filler gauge

Question 24. In what ways can filing be done?
Answer . Draw filing, straight filing, cross filing, circular filing

Question 25. The edges of the sheet are folded together specially and what is it called?
Answer . The seam

Question 26. What is ahead file called?
Answer . Safe as file

Question 27. How is the screw raid cut on the cylindrical surface?
Answer . Helical grooves

Q 28. What is the shape of the head hall of the head hammer?
Answer . Elliptical

Question 29. Which is the possibility of slipping in the drive?
Answer . belt drive

Question 30. What is the Draft Punch used for?
Answer . To hall together thin sheets

Question 31. Which metal is made of soldering iron tip?
Answer . Copper

Question 32. What is the distance between one dot punch to another dot punch?
Answer . 3 to 5mm

Question 33. At what temperature is the gauge kept in the workshop?
Answer . 20 ° C

Question 34. What is the ratio of round taper?
Answer . 1:50

Question 35. Which bolt has 6 aspects which are used in ordinary works?
Answer . Hexagonal head voltage

Question 36. For which work the helical torsion spring is used?
Answer . Carried out in a bicycle career

Question 37. Does Sk pitch gauge have a range of bangles?
Answer . 0.25mm to 6mm

Question 38. To what degree can the blade of the trip be ground?
Answer . At 80 degrees

Question 39. Which punch is used to confirm marking done on the job?
Answer . Dot punch

Question 40. Which spring is used for?
Answer . It is mostly used in automobiles

Question 41. What is the size of the C clamp?
Answer . C size

Question 42. What type of tool is a steel rule?
Answer . Direct scale

Question 43. What is the top angle of the Iron V block?
Answer . 90 degrees

Question 44. Haxoblade width can be up to how many mm?
Answer . 13mm to16mm

Question 45. According to Standard Institute, the radius is found in which range?
Answer . 0.6mm to 25mm

Question 46. How many bangles are in medium type in taper?
Answer . 3 to 4 bangles

Question 47. Bearing loose pully is that which runs in the form?
Answer . freeform

Question 48. Which punch is used for soft metal?
Answer . Pick punch

Question 49. The cutting edge of rice is made?
Answer . Convex

Question 50. At what length are chisels found?
Answer . 150 to 200mm

Question 51. What is the setting of the teeth of a blade called?
Answer . Setting of teeth

Question 52. The small difference is enlarged and corrected?
Answer . dial test indicator

Question 53. The machine tool slide is used to vertical and horizontal aligners?
Answer . Block-level experiment

Question 54. What is the melting point of the solder?
Answer . 205 to 450

Question 55. Two gears are used to transmit speed at a 90-degree angle or set at a particular angle. Which gear is used?
Answer . Bevel gear

Question 56. Which is used to remove burnt coal pieces near the nozzle?
Answer . Rack and poker

Question 57. Think rule is used by-
Answer . patternmaker

LEAVE A REPLY

Please enter your comment!
Please enter your name here